The Senco DS722 18V cordless collated screw gun delivers up to 2500rpm with an 8.13Nm high torque motor, driving screws from 25mm to 75mm. Supplied with two 3.0Ah batteries, a 60-minute charger, and carry case.
The Senco DS722 18V cordless collated screw gun is a serious piece of kit built for tradespeople who are putting in screws by the hundred rather than the handful. With an 8.13Nm high torque motor designed specifically not to bog down mid-drive, it runs at up to 2500rpm no-load and can knock out between 600 and 1400 drives per battery charge depending on your application. That is a lot of decking, drywall, or framing before you are reaching for the spare pack.
Screw diameter range is 3.5mm to 4.8mm and screw length runs from 25mm to 75mm, which covers the vast majority of collated work you will encounter on site. The variable speed trigger gives you genuine control, which matters when you are self-tapping into steel rather than driving into timber. There is also a trigger lock for sustained use, which saves your finger on longer runs.
What Makes the Senco DS722 Worth Carrying
The depth of drive is adjustable with a depth lock, so you can dial in flush drive or countersink and trust it to stay consistent across the whole job. The tool-free adjustable nosepiece has easy-read length markings, and the quick slide bit release is genuinely clever — push the slide and the bit simply drops out. No fiddling. The super hard drive bits supplied are noticeably more durable than standard bits, and the corner fit feed system gives you better access and sightlines in tight spots. There is a reverse switch for backing out screws, which you will appreciate at least once every job.
At 2.58kg it is light enough to use all day without your arm hating you by lunchtime. The ergonomic grip and secondary hand grip reduce fatigue on extended runs, and the belt hook keeps it within reach rather than on the floor somewhere. Supplied with two 3.0Ah lithium-ion batteries, a 60-minute charger, drywall and wood nose adaptors, three PH2 bits, and a carry case.
Pro Tip: When switching between drywall and timber applications, swap the nosepiece adaptor and reset your depth of drive before the first fastener — the two materials behave differently under the collated feed and a quick reset saves a lot of countersinking corrections.
The Senco DS722 is used across a wide range of fast-fix applications on construction sites and fit-out projects. Drywall installation is the obvious one, with collated screwing making light work of boarding out stud walls, ceilings, and partitions at speed. It is equally at home on timber decking, engineered flooring, and structural timber framing where consistent depth and screw placement matter. The variable speed trigger and steel self-tapping capability make it useful for light steel stud work as well, so it earns its place on the van for both ground-works and first-fix fit-out trades.
Best For
Drywall and plasterboard boarding
Timber decking and flooring
Structural timber framing
Light steel stud work
Self-tapping into steel
Compatible With
Collated screws 25mm to 75mm length
Screw diameter 3.5mm to 4.8mm
PH2 collated screw strips
Drywall nose adaptor (included)
Wood nose adaptor (included)
Senco 18V Li-ion battery platform
Key Specifications
Motor torque: 8.13Nm
No-load speed: 0 to 2500rpm
Battery: 18V Li-ion, 2 x 3.0Ah included
Charger: 60-minute fast charge
Weight: 2.58kg
Drive rate: 600 to 1400 drives per charge
Not suitable for: Not suitable for lag bolts, heavy structural fasteners, or screws outside the 3.5mm to 4.8mm diameter range. Not designed for use with non-collated loose screws.
Fit the correct nosepiece adaptor for your application, drywall or timber, and load your collated strip into the feed magazine. Set the depth of drive using the adjustable nosepiece and lock it off before you start your run. Run a test drive on a spare piece of material to confirm depth is where you need it.
Use the variable speed trigger to moderate RPM when driving into steel or denser materials. For repetitive boarding work, engage the trigger lock once you are confident in your depth setting and let the tool do the work. When you need to back a screw out, the reverse switch is positioned to reach without changing your grip.
Fit the appropriate nose adaptor for your application using the tool-free adjustment system
Load the collated screw strip into the magazine feed
Adjust the depth of drive using the nosepiece length markings and engage the depth lock
Run a test drive on a scrap piece of material to verify depth and flush setting
Use the variable speed trigger to moderate RPM when driving into steel or dense timber
Engage the trigger lock for sustained run boarding work once depth is confirmed
Use the reverse switch to back out any misdriven screws without changing grip
Release the bit using the quick slide mechanism when swapping between bit types
Uncoil the belt hook and hang the tool when moving between work areas rather than setting it on the floor
What batteries does the Senco DS722 come with, and how long do they take to charge?
The DS722 is supplied with two 3.0Ah 18V lithium-ion batteries and a 60-minute charger. Two batteries means you can keep one on charge while the other is in the tool, which matters on bigger boarding jobs where downtime adds up.
Can the Senco DS722 be used for both drywall and timber applications?
Yes. The tool is supplied with both a drywall nose adaptor and a wood nose adaptor, and the depth of drive is independently adjustable for each. The variable speed trigger also helps when moving between materials that require different driving pressures.
The DS722 uses an 8.13Nm high torque motor with a variable speed range of 0 to 2500rpm, engineered to maintain drive consistency without bogging down under load. The cordless platform runs on Senco 18V lithium-ion batteries with the supplied 3.0Ah packs providing 600 to 1400 drives per charge depending on screw length and substrate. The collated feed system uses a corner fit design to maintain positive screw engagement and improved sightlines during operation.
Voltage
18V
Battery capacity
2 x 3.0Ah Li-ion
No-load speed
0 to 2500rpm
Motor torque
8.13Nm
Screw diameter range
3.5mm to 4.8mm
Screw length range
25mm to 75mm
Drive rate per charge
600 to 1400 drives
Weight
2.58kg
Charger time
60 minutes
Included accessories
Drywall nose adaptor, wood nose adaptor, 3 x PH2 bits, 2 x 3.0Ah batteries, carry case
Product Type
Cordless Power Tools
Reviews
There are no reviews yet.
Be the first to review “Senco DS722 18V Li-ion Cordless Collated Screw Gun 2500rpm 75mm”Cancel Reply
Reviews
There are no reviews yet.