Timco Solo collated woodscrews in a single thread, double countersunk design for use in timber and man-made boards. Compatible with all leading collated screwdrivers. Available in a range of sizes from 4.2 x 40mm up to 4.5 x 70mm.
Size
QTY
Price
QTY
4.2 x 40mm
1000
£15.22£18.26
4.2 x 50mm
1000
£17.23£20.68
4.2 x 55mm
1000
£18.02£21.62
4.5 x 60mm
500
£11.63£13.96
4.5 x 70mm
500
£13.43£16.12
Timco Solo collated woodscrews are a go-to fixing for anyone running a collated screwdriver on site. Designed as a single thread screw with a double countersunk head, they drive cleanly into timber and sheet materials without splitting or mushrooming the surface. If you’re fixing chipboard flooring, MDF, OSB or softwood framing at any kind of pace, these make the job noticeably quicker.
The collated strips are built to work with all leading power tool brands, so there’s no faffing about with compatibility. Load the strip, drive the screw, move on. That’s the whole point of a collated system, and Timco have done the straightforward thing of making sure the strips actually fit the tools people already own.
Where Timco Solo Collated Woodscrews Get Used
The dual thread design helps pull material tight as the screw seats, which is useful when fixing sheet goods to joists or battens where you need a firm clamp rather than just a hold. The yellow zinc coating gives reasonable protection against moisture during construction, though these aren’t intended as an external or structural fixing.
Size Range and Pack Options
Timco Solo collated woodscrews are available in five sizes from 4.2 x 40mm through to 4.5 x 70mm, covering most first and second fix timber applications. Pack quantities run at 500 or 1000, which suits both smaller jobs and larger runs where you’d rather not stop to restock. At this price point, buying in bulk is a straightforward call.
The PH drive and double countersunk head keep things simple. No torx, no square drive, no hunting for a specific bit. A standard PH2 bit is all you need, and most collated guns take care of the rest.
Pro Tip: Always fully uncoil or extend your cable before use and check your collated gun's depth setting on a scrap piece of the same board before you start, because chipboard and MDF vary in density and a screw driven too deep will lose its hold.
Timco Solo collated woodscrews are used across first and second fix carpentry, flooring installations and general timber construction. They're particularly well suited to fixing chipboard flooring panels, OSB decking, MDF sheet goods and softwood stud work where speed matters and a consistent drive depth is important. Joiners, flooring fitters and site carpenters reach for collated screws when they're covering large areas and need to keep moving without reloading a standard screwdriver bit every few fixings.
Best For
Chipboard flooring
OSB and MDF sheet fixing
Softwood timber framing
Battens and noggins
First and second fix carpentry
Compatible With
All leading collated screwdriver brands
Standard PH2 drive bits
Collated screw gun magazines
Key Specifications
Single thread design
Double countersunk head
PH (Pozidrive) drive
Yellow zinc coating
Sizes: 4.2 x 40mm to 4.5 x 70mm
Pack sizes: 500 or 1000
Not suitable for: Not suitable for external structural applications or where a Class 4 corrosion-resistant fixing is required. Not recommended for use in hardwoods without pre-drilling.
Set your collated screwdriver to the correct depth for the board thickness you're working with. Test on an offcut first to confirm the screw seats flush without breaking the surface. Keep the gun perpendicular to the material to avoid the screw driving at an angle, which can cause the strip to jam or the screw to miss the joist below.
Select the correct screw size for your material thickness and substrate beneath
Load the collated strip into the magazine of your screwdriver or screw gun
Set the drive depth on a scrap piece of the same board before starting
Hold the gun perpendicular to the surface and drive each screw in a single smooth action
Check the first few fixings are sitting flush before continuing across the full area
Store unused strips in a dry location to prevent the coating from deteriorating before use
Are the collated strips compatible with my brand of screw gun?
Yes. Timco Solo collated strips are designed to be compatible with all leading collated screwdriver and screw gun brands. If you're using a Dewalt, Makita, Senco or similar collated gun, the strips should load and feed without issue.
Can these screws be used for chipboard flooring?
Yes, chipboard flooring is one of the main applications these screws are designed for. The single thread and double countersunk head drive cleanly through chipboard and seat flush at the surface, which is exactly what you need when laying a floor that needs to be flat and tight.
Timco Solo collated woodscrews are manufactured with a single thread profile and double countersunk head geometry, designed to drive efficiently through timber and man-made board materials. The yellow zinc coating provides basic corrosion resistance suitable for internal construction conditions. The PH drive recess is compatible with standard PH2 collated gun bits.
Drive Type
PH (Pozidriv)
Head Type
Double Countersunk
Thread Type
Single Thread
Coating
Yellow Zinc
Available Sizes
4.2 x 40mm, 4.2 x 50mm, 4.2 x 55mm, 4.5 x 60mm, 4.5 x 70mm
Pack Quantities
500, 1000
Collated
Yes
Size
4.5 x 60mm, 4.5 x 70mm, 4.2 x 40mm, 4.2 x 50mm, 4.2 x 55mm
Box Quantity
1000, 500
Reviews
There are no reviews yet.
Be the first to review “Timco Solo Collated Chipboard & Woodscrews – PH – Double Countersunk – Yellow”Cancel Reply
From £8.98£10.78 EX VATINC VAT Select options This product has multiple variants. The options may be chosen on the product page
Reviews
There are no reviews yet.