Lightweight microporous laminate coverall with Type 5/6 chemical splash protection. Anti-static, latex-free, and CE Category III certified. Elasticated hood, cuffs and ankles with a two-way zip and re-sealable stormflap.
Available options and pricing for Chemical Splash Resistant Disposable Coverall - Type 5/6 - White, with quantity selectors and a running total
Size
SKU
Price
QTY
Total
medium 92 100cm
SCAWWDOM56
£2.49£2.99
—
large 100 108cm
SCAWWDOL56
£2.49£2.99
—
x large 108 115cm
SCAWWDOXL56
£2.49£2.99
—
x x large 115 124cm
SCAWWDOXXL56
£2.49£2.99
—
The Scan white chemical splash coverall is built from a microporous laminate fabric that sits in a useful middle ground: light enough to wear for a full shift without feeling like you’re wrapped in a bin bag, but strong enough to meet the standards that matter on serious jobs. Type 5 and Type 6 certified, it handles both airborne particles and liquid chemical splash, which means one suit covers a reasonable range of hazardous environments.
It’s CE PPE Category III rated, which is the classification reserved for protection against the highest levels of risk. That’s not a marketing distinction; it affects which environments you’re legally permitted to use the suit in. For asbestos removal, chemical handling, biohazard work, or anything involving fine particulates and splash risk, you want a suit sitting in that category rather than something cheaper that only holds a Category II mark.
The anti-static properties are certified to EN 1149-1:2008, making it suitable for environments where static discharge is a concern — aerospace and electronics manufacturing being the obvious ones, but also certain chemical processing facilities where the combination of flammable vapours and static electricity is best avoided. It’s also latex and silicone free, which removes a potential irritant issue for anyone with sensitivities.
Where This White Chemical Splash Coverall Gets Used
The construction and fit is practical. A three-piece elasticated hood keeps the head coverage secure without gaps at the neck. Knitted cuffs at the wrists stop the sleeves riding up or letting particulates in. Elasticated ankles do the same job at the other end. The two-way zip with a re-sealable adhesive stormflap means you can actually get in and out of the suit cleanly, which matters when you’re doffing in a decontamination zone and don’t want to contaminate yourself on the way out.
It’s a single-use disposable suit, which is the correct approach for most hazardous environments. Trying to decontaminate and reuse a suit of this type introduces variables you don’t want. One job, one suit — simple enough.
Pro Tip: When doffing after asbestos or biohazard work, always roll the suit inward as you remove it to trap any surface contamination inside, and bag it immediately rather than leaving it on the floor of the work area.
This coverall is used across a wide range of industries where workers need protection from chemical splash, airborne particles, or biological hazards. Asbestos removal contractors, chemical plant workers, laboratory technicians, disaster response teams, and forensic investigators all reach for a suit in this category. It's equally common in waste management, pharmaceutical manufacturing, and industrial cleaning where particulate or liquid hazard is a daily reality.
The anti-static certification opens it up for use in aerospace assembly, electronics facilities, and certain petrochemical environments. For disease and disaster management operations, the biohazard certification to EN 14126 makes it appropriate where biological contamination control is required.
Best For
Asbestos removal
Chemical handling and splash risk
Biohazard and disease management
Forensic work
Waste management
Aerospace and electronics assembly
Pharmaceutical and laboratory environments
Available In
Medium (92-100cm)
Large (100-108cm)
X Large (108-115cm)
XX Large (115-124cm)
White
Key Features
CE PPE Category III
Type 5 certified (EN 13982-1)
Type 6 certified (EN 13034)
Anti-static EN 1149-1:2008
Biohazard rated EN 14126
Latex and silicone free
Two-way zip with re-sealable stormflap
Elasticated 3-piece hood, ankles and back
Not suitable for: Not suitable for reuse — this is a single-use disposable suit and should be disposed of after each job. Not designed for protection against pressurised liquid jets or total liquid immersion.
Before putting the suit on, check it for any packaging damage or tears. Work out which size you need based on the chest measurements provided — a suit that's too tight will stress the seams and risk splitting, while one that's too large creates excess material that can snag.
Put the suit on in a clean area before entering the hazard zone. Pull the hood up and secure it fully, making sure there are no gaps at the neck. Fasten the zip fully and seal the stormflap over it. Tuck knitted cuffs under your gloves and ensure ankle elastics are sitting correctly over your boot covers or footwear.
When removing the suit, roll it inward from the shoulders to contain any surface contamination. Dispose of it in an appropriate waste bag for the hazard type involved. Do not attempt to clean or reuse it.
Inspect the suit for damage before use — any tears or defects and it goes in the bin, not on your body
Select the correct size based on the chest measurement guide
Step into the suit in a clean area before entering the contaminated zone
Pull the three-piece hood fully over your head and ensure it sits securely with no gap at the neck
Fasten the two-way zip fully from bottom to top
Seal the adhesive stormflap over the zip
Tuck knitted cuffs inside your gloves to maintain the barrier at the wrist
Check ankle elastics are seated correctly over footwear or boot covers
On removal, roll the suit inward from the shoulders to contain surface contamination
Bag and dispose of the suit according to the waste handling requirements for the specific hazard
What is the difference between Type 5 and Type 6 protection?
Type 5 (EN 13982-1) covers protection against airborne solid particulates, including fine dusts like asbestos fibres. Type 6 (EN 13034) covers protection against light liquid chemical splash. This suit is certified for both, so it handles environments where you're dealing with either or both hazards at the same time.
Is this suit suitable for asbestos removal work?
Yes. The Type 5 certification to EN 13982-1 makes it appropriate for use during asbestos removal work. It is CE PPE Category III rated, which is the category required for protection against irreversible or life-threatening risks. Always follow your site's specific PPE requirements and disposal procedures.
Can this coverall be worn more than once?
No. This is a single-use disposable suit. Once it has been worn in a hazardous environment, it should be removed carefully to avoid self-contamination and disposed of correctly. Reuse introduces risk of contamination transfer and is not appropriate for a suit of this type.
Manufactured from a microporous laminate material, the suit provides a barrier to both airborne particles and liquid splash without the heavy, impermeable feel of a fully encapsulating suit. The non-linting construction makes it suitable for cleanroom-adjacent environments. Certified to CE PPE Category III, Type 5 (EN 13982-1), Type 6 (EN 13034), anti-static (EN 1149-1:2008), and biohazard (EN 14126). Free from latex and silicone.
Certification
CE PPE Category III
Type 5 Standard
EN 13982-1
Type 6 Standard
EN 13034
Anti-Static Standard
EN 1149-1:2008
Biohazard Standard
EN 14126
Material
Microporous laminate
Colour
White
Closure
Two-way zip with re-sealable adhesive stormflap
Hood
Elasticated 3-piece
Cuffs
Knitted
Latex Free
Yes
Silicone Free
Yes
Sizes Available
Medium (92-100cm), Large (100-108cm), XL (108-115cm), XXL (115-124cm)
Use
Single use disposable
Size
large 100 108cm, medium 92 100cm, x large 108 115cm, x x large 115 124cm
Box Quantity
1
Reviews
There are no reviews yet.
Be the first to review “Chemical Splash Resistant Disposable Coverall – Type 5/6 – White”Cancel Reply
Reviews
There are no reviews yet.