Cleanfit abrasive mini strip in a handy 5m roll. Waterproof, washable and non-clogging open mesh construction works on both sides, wet or dry. A reliable step up from steel wool, emery cloth and standard sandpaper for plumbing and general trade use.
QTY
Price
QTY
1
£7.49£8.99
10
£64.90£77.88
The Cleanfit abrasive mini strip is one of those products that quietly earns its place in the toolbag without much fuss. This 5m roll gives you a generous length of open mesh abrasive that you can cut down to whatever size the job demands, whether that is cleaning the end of a 15mm copper pipe or getting into a tight fitting on older pipework. It works on both sides, handles wet and dry conditions without complaint, and once you have used it, going back to emery cloth feels a bit like going back to dial-up internet.
The mesh construction is what makes this genuinely different from sandpaper or steel wool. Standard emery cloth clogs almost immediately when used on soft metals or in damp conditions. The open weave of the Cleanfit abrasive mini strip lets swarf and debris fall away rather than build up on the surface, so the abrasive keeps cutting instead of just skidding about. It is also washable, which means if you are doing a long run of joints, you are not burning through strip after strip.
Where Cleanfit Abrasive Mini Strip Fits Into the Job
Plumbers reach for this most often when prepping copper pipe and fittings before soldering. Getting the oxide layer off cleanly and consistently is the difference between a joint that holds and one that weeps six months later. The Cleanfit strip does that reliably, and because it is flexible enough to wrap around pipe ends and work inside sockets, it gets into places where a flat sheet is useless.
Not Just for Plumbing
Electricians use it for cleaning terminal connections and stripping back oxidation on cable ends. It is handy on any job where you need a controlled, light abrasive action without the risk of leaving steel fibres behind, which is a genuine concern with traditional wire wool near any kind of electrical work.
The 5m roll format means you are not rationing yourself to a tiny strip off a sheet. Cut what you need, use it properly, and move on. Simple as that.
Pro Tip: When prepping copper pipe for soldering, wrap the Cleanfit strip around the pipe end and rotate it in short back-and-forth movements rather than scrubbing along the length, this way you get even abrasion all the way around without leaving directional score marks that can cause flux to sit unevenly.
Cleanfit abrasive mini strip is used most regularly by plumbers cleaning copper pipe ends and fittings ahead of soldering or press fitting. The waterproof mesh copes well with the damp conditions you often find when working on existing systems. It is equally useful for light deburring, surface prep on brass fittings, and cleaning corroded or oxidised connections where emery cloth would clog before the job is done.
Electricians use it for terminal cleaning and removing surface oxidation from cable ends and bus bars. It is also widely used in general maintenance work where a flexible, controllable abrasive is needed in a confined space or on an irregular surface.
Best For
Prepping copper pipe and fittings for soldering
Cleaning oxidised connections and terminals
Deburring brass and copper fittings
Light surface preparation in wet conditions
Working in tight or awkward spaces
Works With
Copper pipe and fittings
Brass valves and connectors
Electrical terminals and cable ends
Steel and aluminium surfaces
Wet and dry conditions
Key Features
Open mesh, non-clogging construction
Abrasive on both sides
Waterproof and washable
Flexible enough to wrap around pipe
5m roll for cut-to-length use
High performance alternative to steel wool and emery
Not suitable for: Not suitable for heavy material removal or coarse grinding applications. The open mesh construction is designed for surface cleaning and prep rather than aggressive stock removal, so it will not replace a proper abrasive disc or flap wheel where significant material needs to come off.
Cut a workable length from the roll, typically 150 to 200mm is enough for most pipe prep work. Wrap it around the pipe end or fitting socket and work it back and forth with light, even pressure. The mesh cuts on both sides, so flip it over when one face loads up or loses its bite.
In wet conditions it can be rinsed out and reused, which makes a single cut length go further than you might expect. For terminal or connection cleaning, fold the strip to a manageable pad and work it into the contact surface with short strokes. Wipe away any debris before applying flux or making the final connection.
Cut the required length from the roll using snips or scissors
For pipe prep, wrap the strip around the pipe end with the abrasive face against the metal
Work the strip back and forth using short strokes with even pressure
Rotate around the pipe as you go to ensure consistent coverage
Flip the strip over when one side begins to lose its cut
Rinse and squeeze out the strip if working in wet conditions to extend its life
Wipe the prepared surface clean before applying flux or making the joint
Can the Cleanfit abrasive mini strip be used on stainless steel or plastic pipe?
It will work on stainless steel for light surface cleaning, though stainless is harder and will wear the strip faster than copper or brass. It is not intended for use on plastic pipe, where abrasion is generally not required and could damage the surface.
How does it compare to standard emery cloth for plumbing work?
The main practical difference is clogging. Emery cloth loads up quickly, particularly in damp conditions or on soft metals like copper. The open mesh on the Cleanfit strip lets debris fall away, so it keeps cutting for longer and can be washed out and reused rather than binned after a single joint.
Is there any risk of leaving metallic fibres behind when using it near electrical connections?
Unlike steel wool, the Cleanfit strip does not shed loose metallic fibres, which makes it a safer choice around terminals, bus bars, and cable connections where stray wire fragments could cause a fault. Always wipe down the surface after use before making any electrical connection.
Cleanfit abrasive mini strip uses an open weave mesh substrate rather than a solid backing, which allows the abrasive grit to work on both faces simultaneously and prevents the surface loading that limits traditional emery cloth and sandpaper. The waterproof construction means the bond between grit and substrate holds under wet working conditions, and the strip can be rinsed without degrading. It is designed specifically as a high performance replacement for steel wool and emery in plumbing and light trade applications.
Brand
Cleanfit
Format
Roll
Roll Length
5m
Construction
Open mesh abrasive
Sides
Double-sided
Waterproof
Yes
Washable
Yes
Application
Wet and dry
Weight
N/A
Size
5m roll
Box Quantity
1, 10
Reviews
There are no reviews yet.
Be the first to review “Cleanfit Waterproof Abrasive Mini Strip 5m Roll”Cancel Reply
Reviews
There are no reviews yet.