Converts an SDS drill chuck to accept a 1/2 inch BSP male fitting, allowing TCT and diamond core drill bits to be used with a standard SDS rotary hammer. Simple, effective and easy to fit on site.
The diamond core SDS chuck adaptor is a small but genuinely useful bit of kit for anyone using TCT or diamond core drill bits with an SDS rotary hammer. It converts your SDS chuck fitting to a 1/2 inch BSP male thread, which is the standard connection used by most core drill barrels and TCT hole saws. Without something like this, you are either limited to dedicated core drill machines or stuck trying to bodge a connection that was never designed to work.
Core drilling comes up on all sorts of jobs. Running cables through masonry, installing soil pipes, fitting air bricks, putting through conduit in blockwork walls. In most of these situations, the SDS hammer drill is already on site and ready to go. This adaptor means you can pick up a diamond core bit and get straight to work rather than hunting for a separate machine. That is the kind of thing that saves real time, not in any dramatic way, just the quiet satisfaction of not having to go back to the van twice.
Diamond Core SDS Chuck Adaptor in Use
The adaptor fits into the SDS chuck of your hammer drill the same way any SDS accessory does. The 1/2 inch BSP male thread on the other end connects directly to the threaded connection on your core barrel. Make sure the barrel is properly seated and you are good to go. It works with TCT core bits as well as diamond segment barrels, which makes it handy across a range of materials.
For best results, use the drill in rotary mode only when running diamond core bits, not hammer action. Diamond cores cut by abrasion and hammering will damage the segments fast. TCT core bits can handle rotary hammer mode on softer materials, but it is worth checking the bit manufacturer guidance. The diamond core SDS chuck adaptor itself is straightforward and reliable, doing exactly the one job it is there to do.
Pro Tip: Always switch your SDS drill to rotary-only mode when using diamond core bits with this adaptor, hammer action will destroy the diamond segments within seconds.
This adaptor is used by electricians, plumbers, builders and groundworkers who need to run core drill bits from an SDS rotary hammer rather than a dedicated core drill machine. It suits jobs where a full core drilling rig would be overkill, such as single cable or pipe penetrations through brick, block or concrete. It is equally useful for TCT hole saws going through timber-frame structures or lintels. Any trade that carries an SDS drill and occasionally needs to core through masonry will find a use for this.
Best For
Cable and conduit penetrations through masonry
Soil pipe and waste pipe installations
Air brick and vent openings
Single core holes where a dedicated rig is not warranted
Compatible With
SDS rotary hammer drills
Diamond core drill barrels with 1/2 BSP female thread
TCT core drill bits with 1/2 BSP connection
Standard SDS chuck format
Key Specifications
Drive fitting: SDS
Output thread: 1/2 inch BSP male
Suitable for diamond core and TCT core bits
Not suitable for: Not suitable for use as a replacement for a dedicated core drill machine on heavy or prolonged coring work, as SDS drills are not designed to sustain the torque loads involved over extended periods. Not suitable for core bits using connection standards other than 1/2 inch BSP.
Fit the SDS shank end of the adaptor into your drill chuck and lock it in place as you would any SDS bit. Thread your core barrel or TCT bit onto the 1/2 inch BSP male end and tighten it securely by hand. Select rotary-only mode on the drill before you start, particularly important with diamond core bits. Begin drilling at a steady, controlled pace with consistent forward pressure and let the bit do the cutting.
Insert the SDS shank end of the adaptor into your drill chuck and lock it firmly
Thread the diamond core or TCT barrel onto the 1/2 inch BSP male thread and hand-tighten
Set your SDS drill to rotary-only mode, not hammer action, especially with diamond core bits
Mark your drilling position clearly and start at slow speed to establish the cut
Maintain steady forward pressure and allow the bit to cut at its own pace
For diamond core bits, apply water cooling where possible to extend segment life
Will this adaptor work with any SDS drill?
Yes, it fits the standard SDS chuck format found on the vast majority of SDS rotary hammer drills on the market. If your drill takes standard SDS bits, this adaptor will fit it.
Can I use this with hammer action turned on?
For diamond core bits, no. Diamond segments cut by abrasion and hammer action will wreck them almost immediately. TCT core bits are more tolerant of hammer mode on softer materials, but rotary-only is the safer default for both.
What size core barrels does the 1/2 inch BSP thread fit?
The 1/2 inch BSP male thread is the standard connection used across most diamond core barrels and TCT hole saws, so it is compatible with the majority of brands and sizes you will encounter on site. Always check that the specific barrel you are using has a 1/2 inch BSP female thread before purchasing.
The adaptor bridges the SDS drive format, standard on most rotary hammer drills, to the 1/2 inch BSP male thread used by diamond core barrels and TCT core bits. BSP stands for British Standard Pipe and is the thread standard used across the UK core drilling accessory market. The adaptor is a compact, machined steel component designed to transfer rotational drive from the drill to the core bit without excessive play or vibration.
Drive Type
SDS
Output Thread
1/2 inch BSP male
Compatible Bit Types
Diamond core, TCT core
SKU
DCA-SDS
Product Type
Diamond Core Adaptors
Reviews
There are no reviews yet.
Be the first to review “Diamond Core Drill SDS Chuck Adaptor”Cancel Reply
Reviews
There are no reviews yet.