WRAS approved end feed adaptor couplers for connecting copper pipe to BSP male iron threads. Available in 15mm x 1/2″, 22mm x 1/2″ and 28mm x 1″ sizes. Sold in boxes of 25 for trade convenience.
Available options and pricing for End Feed adaptor coupler, with quantity selectors and a running total
Size
SKU
Price
QTY
Total
15mm x 1/2" IMP
30403101
£7.20£8.64
—
22mm x 1/2" IMP
30403105
£10.00£12.00
—
28mm x 1" IMP
30403109
£13.60£16.32
—
The end feed adaptor coupler is one of those fittings that turns up on almost every domestic and commercial plumbing job. It bridges the gap between copper pipe and BSP male iron threads, letting you connect a copper run to a gate valve, boiler, pump, or pretty much any threaded component without a second thought. These are WRAS approved, which means they meet the Water Regulations Advisory Scheme requirements for use in potable water systems in the UK. That matters on any job where building control is involved, or where the end client expects the paperwork to stack up properly.
End feed fittings work by soldering directly onto the copper pipe. There’s no pre-loaded solder ring to rely on, so you apply your own solder and flux, heat the fitting, and feed the solder in. That gives you complete control over the joint and makes it straightforward to achieve a clean, leak-free connection when the preparation is right. The copper alloy construction conducts heat well during soldering and gives you a fitting that holds up under the pressures and temperatures you’d expect in a standard central heating or hot and cold water installation.
Where the End Feed Adaptor Coupler Gets Used
These fittings are available in three sizes to cover the most common transition points you’ll encounter. The 15mm x 1/2″ BSP is the one you’ll reach for most often, used on radiator valves, isolation valves, tap connectors, and branch connections throughout a standard domestic installation. The 22mm x 1/2″ BSP suits connections on pump heads, motorised valves, and various heating components where a 22mm copper run meets a half-inch threaded port. The 28mm x 1″ BSP is the larger option, used on main flow and return connections, cold water mains headers, and larger commercial or industrial plumbing runs.
Buying in boxes of 25 makes sense if you’re stocking a van or working through a new build or refurbishment where the same size fitting appears repeatedly. Running out of a 15mm adaptor mid-job because you grabbed a bag of five from a merchant is the sort of thing that ends a productive morning fairly quickly.
WRAS approval gives you confidence that the materials won’t contaminate the water supply and that the fittings are fit for purpose in any potable or heating system you’re working on. Worth having the box to hand on the van rather than hunting one down when you need it.
Pro Tip: Always clean and flux both the pipe end and the inside of the fitting socket before heating. End feed fittings give you nothing to fall back on if the preparation is poor, so a clean, properly fluxed joint is the difference between a solid connection and a callback.
End feed adaptor couplers are used wherever a copper pipe run needs to connect to a BSP male threaded component. That covers radiator valves, isolation valves, gate valves, pump heads, motorised valves, boiler flow and return connections, cold water mains pipework, and commercial heating systems. Plumbers and heating engineers fit these as a matter of course on new installations, system replacements, and partial refurbishments across domestic, commercial, and light industrial properties.
Best For
Connecting copper pipe to BSP male threaded fittings
Domestic hot and cold water systems
Central heating flow and return pipework
Boiler and pump connections
Isolation and gate valve installations
Available In
15mm x 1/2" BSP
22mm x 1/2" BSP
28mm x 1" BSP
Key Features
WRAS approved for potable water systems
End feed solder construction
Copper alloy material
Suitable for hot and cold water and central heating
Sold in trade boxes of 25
Not suitable for: Not suitable for use with plastic or push-fit pipe systems. These fittings require soldering and are intended for copper pipe installations only.
Cut the copper pipe square, deburr the end, and clean the outside of the pipe and the inside socket of the fitting with wire wool or abrasive cloth until both surfaces are bright. Apply flux to both the pipe and the fitting socket before assembling. Heat the fitting evenly with a blowtorch until the flux begins to sizzle, then feed solder into the joint gap until it appears all the way around the socket mouth. Allow the joint to cool undisturbed before testing.
Wrap the male BSP thread with PTFE tape before making up the threaded connection, applying several even turns in the direction of the thread. Nip the fitting up hand-tight first, then tighten with a spanner. Over-tightening a threaded brass fitting is a quick way to crack it, so firm and controlled is the right approach rather than maximum torque.
Cut copper pipe to length using a pipe cutter for a clean, square end
Deburr the pipe end inside and out with a deburring tool or file
Clean the outside of the pipe end and the inside of the fitting socket with wire wool or emery cloth until both are bright copper
Apply solder flux to the cleaned pipe end and inside the fitting socket
Push the pipe fully into the fitting socket
Apply heat evenly around the fitting body with a blowtorch until flux starts to sizzle
Feed solder into the joint gap until it draws in and appears cleanly around the full socket mouth
Remove heat and allow the joint to cool without disturbing it
Apply PTFE tape to the male BSP thread in the direction of the thread before making up the threaded connection
Tighten the threaded connection firmly with a spanner without over-tightening
Pressurise the system and check for leaks before covering or burying any pipework
Are these end feed adaptor couplers suitable for use on drinking water installations?
Yes. These fittings carry WRAS approval, which means they are certified for use in potable water systems in the UK. You can fit them on cold water mains, drinking water supplies, and any installation where water quality compliance is required.
What is the difference between an end feed fitting and a solder ring fitting?
A solder ring fitting has a pre-loaded ring of solder built into the socket, which melts when heat is applied. An end feed fitting has no pre-loaded solder, so you apply your own solder to the joint as you heat it. End feed fittings give you more control over the amount of solder used and tend to produce a cleaner joint when technique is good.
Manufactured from copper alloy and designed to meet WRAS standards for use in potable and heating water systems. The end feed socket accepts standard copper pipe to BS EN 1057 dimensions and requires the application of flux and solder to complete the joint. The BSP male thread conforms to BS 21 parallel thread form, making it compatible with standard UK plumbing components.
Approval
WRAS Approved
Connection Type
End feed solder x BSP male thread
Available Sizes
15mm x 1/2" BSP, 22mm x 1/2" BSP, 28mm x 1" BSP
Thread Standard
BSP (British Standard Pipe)
Pipe Standard
BS EN 1057 copper pipe
Material
Copper alloy
Box Quantity
25
Suitable For
Hot and cold water, central heating systems
Size
15mm x 1/2" IMP, 22mm x 1/2" IMP, 28mm x 1" IMP
Box Quantity
25
Reviews
There are no reviews yet.
Be the first to review “End Feed adaptor coupler”Cancel Reply
Reviews
There are no reviews yet.