Rooftec angled dry verge ridge end caps for a clean, weatherproof apex finish. Universal fit works on both sides of the gable. Sold in pairs, available in black, brown, grey and terracotta.
Available options and pricing for Dry Verge Ridge End Caps - ANGLED - 2 pcs (Rooftec), with quantity selectors and a running total
Colour
SKU
Price
QTY
Total
Black
RPDVABLACK
£3.98£4.78
—
Grey
RPDVAGREY
£3.98£4.78
—
Brown
RPDVABROWN
£3.98£4.78
—
Terracotta
RPDVATERRA
£3.98£4.78
—
The Rooftec angled dry verge ridge end cap gives your roof apex a proper, finished look while keeping the weather where it belongs — outside. Sold in pairs, these caps sit at the ridge end of a dry verge run, closing off the top of the system neatly without the need for mortar or ongoing maintenance. If you’ve been using Rooftec’s universal dry verge units along the verge, these are the natural finishing piece.
Dry verge systems have largely replaced the old mortar-bedded approach for good reason. No cracking, no pointing to redo every few years, and a much cleaner finish straight off the scaffold. The angled profile on these end caps is designed to follow the roof pitch, so the cap sits flush and doesn’t leave an awkward gap at the top of the run. It’s a small detail that makes a noticeable difference to the overall appearance, especially on new builds or full re-roofing jobs where the client is actually looking at the ridge line.
Where Rooftec Angled Ridge End Caps Fit Into a Dry Verge System
These caps are used specifically at the apex — the very top of the gable end — where the dry verge run meets the ridge. They’re the final piece of the puzzle once the verge units are in place. Without them, you’ve got an open end at the top of the system that looks unfinished and gives wind and water a way in. The angled design means they sit correctly against the ridge rather than leaving a flat cap that doesn’t follow the roof slope.
Rooftec’s dry verge units are universal, meaning each unit works on both left and right-hand sides of the gable. These end caps follow the same principle, so you’re not ordering separate handed components and trying to work out which is which on a Friday afternoon. The 15-year UV protection rating from the manufacturer means colour and structural integrity hold up over time, which matters when the product is sitting on an exposed gable in full sun for years on end. Available in black, brown, grey, and terracotta to match most common tile colours.
Pro Tip: Fit the ridge end cap before you come off the roof — trying to pop one in from a ladder once the scaffold is down is the kind of job that ruins an afternoon.
These angled end caps are used at the apex of a gable end wherever a dry verge system is installed. They're suited to new build roofing, re-roofing projects, and repairs where the existing mortar verge is being stripped and replaced with a dry fix system. Compatible with the full Rooftec universal dry verge range, they work across standard, thin leading edge, and high-profile tile types. Roofers, roofing contractors, and self-build projects all use these as part of a complete dry verge installation.
Best For
Apex finish on dry verge installations
New build roofing
Full re-roofing with dry fix systems
Replacing failed mortar verge finishes
Compatible With
Rooftec universal dry verge units
Standard roof tile profiles
Thin leading edge roof tiles
High-profile roof tiles
Left and right gable ends (universal fit)
Key Features
Angled profile follows roof pitch
Universal — no handed units required
15-year UV protection rating
No mortar required
Available in black, brown, grey, terracotta
Sold in pairs
Not suitable for: These are ridge end caps for the apex of the gable only — they are not suitable as starter units or mid-run verge units. Not intended for use with hip ends or non-gable roof details.
These end caps are fitted as the final step of a dry verge installation, once all verge units are in place along the full length of the gable. The angled profile sits against the ridge, closing off the top of the run. No adhesive or mortar is required as standard, though some installers add a small amount of low-modulus sealant to the back face on exposed sites for additional weather resistance.
Make sure the verge units below are correctly positioned and secured before fitting the end cap. The cap should sit flush with the top unit and follow the pitch of the roof naturally. Check alignment before any fixings are finalised.
Complete the full run of dry verge units along the gable before fitting the end cap
Offer up the angled end cap to the apex to check it sits flush against the ridge and follows the roof pitch
Confirm the cap aligns correctly with the top verge unit below it
Secure the cap in line with the manufacturer's fixing guidance for the verge system in use
On exposed or high-wind sites, apply a small bead of low-modulus sealant to the back face before final fitting
Check the finished installation from ground level to confirm the cap is seated evenly with no visible gaps
Do I need separate left and right-hand end caps for each side of the gable?
No. These are universal, so the same cap works on both sides of the gable end. You won't need to order handed pairs or work out which is which on site.
Will these fit any dry verge system or just Rooftec?
They're designed to work with the Rooftec universal dry verge system. While the profile may be similar to other manufacturers' units, compatibility with third-party systems isn't guaranteed, so it's worth checking before mixing brands on a job.
What colours are available?
Black, brown, grey, and terracotta. These cover the majority of common concrete and clay tile colours used in the UK, so you should be able to match most roofs without issue.
Made from UV-stabilised polymer with a 15-year UV protection rating from the manufacturer. The angled profile is designed to follow the slope of the roof pitch at the gable apex, providing a flush, weatherproof close to the top of a dry verge run. No mortar required. Suitable for use across standard, thin leading edge, and high-profile tile types.
Brand
Rooftec
Pack Quantity
2 pieces
Type
Angled ridge end cap
Fit
Universal (left and right hand)
UV Protection Rating
15 years
Available Colours
Black, Brown, Grey, Terracotta
Fixing Method
Dry fix (no mortar required)
Compatible System
Rooftec Universal Dry Verge
Reviews
There are no reviews yet.
Be the first to review “Dry Verge Ridge End Caps – ANGLED – 2 pcs (Rooftec)”Cancel Reply
Reviews
There are no reviews yet.