Professional laser welded diamond blade engineered for fast cutting through very hard reinforced concrete. Arrow design segments and slanted keyhole cooling slots reduce vibration and keep the blade running cool. Available in sizes from 125mm to 600mm for disc cutters, floor saws and table saws.
Size
Price
QTY
125mm x 22mm
£28.94£34.73
230mm x 22mm
£57.93£69.52
300mm x 20mm
£99.90£119.88
350mm x 20mm
£116.49£139.79
350mm x 25mm
£116.49£139.79
400mm x 25mm
£143.90£172.68
450mm x 25mm
£169.90£203.88
500mm x 25mm
£219.89£263.87
600mm x 25mm
£289.28£347.14
The Premier Diamond P6-ECC EVOCUT ULTRA PRO Reinforced Hard Concrete Diamond Blade is built for one job: getting through very hard reinforced concrete quickly and cleanly. This is a professional-grade blade rated at P6 performance level, laser welded for segment security, and designed to handle the kind of material that will chew through a lesser blade in short order. If you are cutting reinforced slabs, beams, kerbs or heavily rebar-laden concrete on a daily basis, this is the blade spec you want in your angle grinder, floor saw or table saw.
The segment geometry on the EVOCUT blade is where it earns its reputation. The arrow design segments are shaped to bite into hard aggregate efficiently, reducing the effort required from the machine and the operator. Paired with slanted keyhole cooling slots and dedicated cooling holes, the blade manages heat effectively during extended cutting runs. Less heat means longer segment life and less risk of de-bonding under load. In practical terms, that translates to more cuts per blade and fewer stops to let things cool down.
Where the Premier Diamond EVOCUT ULTRA PRO Performs Best
This blade is suited to reinforced concrete in all common construction forms: slabs, pipes, beams, kerbs and precast units. It handles both light and heavy steel reinforcement without the segment damage you can get from a blade that is spec’d too low for the job. Beyond reinforced concrete, the EVOCUT is rated across a broad range of hard construction materials, including engineering bricks, granite, sandstone, York stone, flint aggregate, block paving, flagstones, roof tiles and medium to solid density concrete blocks from 7 Newton upward.
The blade is available in a wide range of diameters, from 125mm up to 600mm, covering handheld disc cutters right through to large floor saws. The bore sizes across the range align with standard machine fittings, so compatibility with common site equipment is straightforward. Whether you are using a 9-inch angle grinder for break-out work or a walk-behind floor saw for cutting expansion joints in a concrete floor, there is a size in this range to match.
Laser Welded Construction
The laser welded bond between segment and blade body is a meaningful distinction on a blade being used in hard, abrasive material. Heat-bonded blades can lose segments when pushed hard or used in reinforced applications. Laser welding significantly reduces that risk, which matters when you are cutting overhead, at depth, or with a floor saw where a lost segment causes serious problems. The P6 classification confirms this blade is engineered for professional, high-demand use rather than occasional DIY cutting.
The Premier Diamond P6-ECC EVOCUT ULTRA PRO Reinforced Hard Concrete Diamond Blade is stocked across the full size range, ready to go. For trade buyers who get through blades regularly, the pricing at this performance tier is worth comparing against what you are currently using.
Pro Tip: Always uncoil and check the blade for cracks or segment damage before fitting, particularly after transit in a toolbox, as even a hairline crack in the steel body can cause blade failure under load.
The EVOCUT ULTRA PRO is used primarily on reinforced concrete in commercial construction, civil engineering and groundwork. Typical applications include cutting concrete road slabs, kerb stones, drainage channels, precast beams and heavily reinforced floor slabs. It is also used for cutting engineering bricks, granite worktops and paving, sandstone, York stone, block paving and flagstones. The blade performs across disc cutters, floor saws and table saws, making it a practical choice for groundworkers, concreters, plant operators and general builders who regularly deal with hard or reinforced materials on site.
Best For
Very hard reinforced concrete
Heavy and light steel reinforcement
Engineering bricks (Class A and B)
Granite blocks and worktops
Sandstone and York stone
Block paving and flagstones
Roof tiles
Medium and solid density concrete blocks (7 Newton+)
Compatible With
Handheld disc cutters and angle grinders
Floor saws
Table saws
22mm bore machines (125mm to 350mm sizes)
20mm bore machines (300mm to 350mm sizes)
25mm and 25.4mm bore machines (350mm to 600mm sizes)
Key Features
P6 professional performance rating
Laser welded segments
Arrow design segment geometry
Slanted keyhole cooling slots and holes
Low vibration during cutting
Available 125mm to 600mm diameter
Not suitable for: Not recommended for soft or green concrete where an abrasive blade specification would perform better. Not intended for cutting ferrous metals, plastics or timber.
Fit the correct blade size for your machine bore and ensure the blade guard is properly secured before starting. Check the blade direction arrow matches the rotation of the machine. For floor saws and disc cutters, set the cutting depth in stages on very hard reinforced concrete rather than attempting full depth in a single pass. This reduces heat build-up and extends segment life.
Keep the blade moving at a consistent pace. Allowing the blade to dwell in one spot generates localised heat and increases the risk of segment wear or warping. Use the cooling slots to your advantage by maintaining steady forward progress. If cutting dry, ensure adequate dust suppression or PPE. Wet cutting with the appropriate machine will extend blade life further on prolonged reinforced concrete work.
Check the blade for cracks, missing segments or damage before fitting
Match the bore size of the blade to your machine spindle and confirm the direction arrow aligns with machine rotation
Secure the blade properly using the correct flange and torque the nut to the machine manufacturer's specification
Set an initial shallow cutting depth for the first pass on very hard or reinforced material
Begin the cut at steady pace, allowing the segments to establish a groove before applying full pressure
Maintain consistent forward movement throughout the cut to avoid heat build-up from dwelling
Increase cutting depth incrementally on thick sections rather than forcing full depth in a single pass
Inspect the blade periodically during extended use for segment wear, cracking or body distortion
What is the difference between the EVOCUT ULTRA PRO and a standard diamond blade for concrete?
The EVOCUT ULTRA PRO is rated at P6 professional performance level and uses laser welded segments with arrow geometry and slanted keyhole cooling slots. Standard or budget blades typically use lower-grade bond hardness and simpler segment shapes, which wear faster in hard or reinforced concrete. The EVOCUT is designed specifically for very hard reinforced concrete where a general-purpose blade would underperform or fail early.
Can this blade be used wet and dry?
The EVOCUT ULTRA PRO is suitable for dry cutting with handheld disc cutters and angle grinders. For floor saw and table saw applications, wet cutting is generally recommended to extend blade life and manage dust on prolonged reinforced concrete cutting jobs. Always check your machine's compatibility with wet or dry use before selecting your cutting method.
Which size should I choose for a standard 9-inch angle grinder or a walk-behind floor saw?
A 230mm x 22mm blade fits a standard 9-inch angle grinder. For walk-behind floor saws, the correct size depends on the machine model, but common floor saw sizes in this range run from 300mm up to 600mm diameter. Check your machine's maximum blade diameter and spindle bore before ordering.
The Premier Diamond P6-ECC EVOCUT ULTRA PRO uses a laser welded construction to bond diamond segments to the steel blade body, providing a more secure join than heat bonding under high-stress cutting conditions. The P6 classification indicates a professional performance tier suitable for continuous use in hard and reinforced concrete. Arrow-profile segments increase cutting efficiency in dense aggregate, while slanted keyhole cooling slots and through-body cooling holes manage thermal load during extended cutting runs.
Brand
Premier Diamond
Model
P6-ECC EVOCUT ULTRA PRO
Segment Type
Arrow design
Bond Type
Laser welded
Performance Rating
P6 Professional
Available Sizes
125mm x 22mm, 230mm x 22mm, 300mm x 20mm, 350mm x 20mm, 350mm x 25mm, 400mm x 25mm, 450mm x 25.4mm, 450mm x 25mm, 500mm x 25mm, 600mm x 25mm
Compatible Equipment
Disc cutter, floor saw, table saw
Primary Application
Very hard reinforced concrete
Size
300mm x 20mm, 350mm x 20mm, 350mm x 25mm, 125mm x 22mm, 230mm x 22mm, 400mm x 25mm, 450mm x 25.4mm, 450mm x 25mm, 500mm x 25mm, 600mm x 25mm
Reviews
There are no reviews yet.
Be the first to review “Premier Diamond P6-ECC EVOCUT ULTRA PRO Reinforced Hard Concrete Diamond Blade”Cancel Reply
Reviews
There are no reviews yet.