Talon pipe cover collars in chrome ABS effect finish, designed to hide where pipes enter or exit walls and floors. Available in sizes from 8mm up to 110mm. Made in the UK from high grade polypropylene. Clean, professional finish every time.
Size
QTY
Price
QTY
35mm
50
£63.10£75.72
42mm
50
£66.90£80.28
35mm
5
£6.46£7.75
42mm
5
£6.96£8.35
110mm
1
£5.73£6.88
8mm
10
£5.52£6.62
10mm
10
£5.52£6.62
12mm
10
£5.52£6.62
15mm
10
£5.52£6.62
18mm
10
£5.83£7.00
22mm
10
£5.44£6.53
28mm
10
£5.44£6.53
Chrome Talon pipe cover collars do one job, and they do it well. Where a pipe disappears through a wall, floor or ceiling, you’re left with a hole that’s rarely tidy. Plaster gets chipped, tiles get drilled slightly too big, or the original collar gets lost somewhere between the van and the job. These snap into place and nobody asks questions. The chrome ABS effect finish looks the part in kitchens, bathrooms and anywhere else a white collar would feel a bit too utilitarian.
Talon manufacture these as a single-piece collar, which keeps installation quick. No assembly, no fidgeting with two halves — just slide it over the pipe before you fix the pipe in place, or use one that opens if you’re retro-fitting. The size range runs from 8mm up to 110mm, so you’re covered whether you’re finishing off a small microbore heating pipe or a larger waste run through a solid floor.
Where Talon Chrome Pipe Cover Collars Are Used
These are a standard finish item on heating and plumbing installations where a professional result is expected. Chrome collars suit central heating pipework in living rooms and hallways, kitchen installations where you want something that doesn’t stand out, and bathroom plumbing where the pipe entry point is visible. Radiator pipework rising through wooden floors is probably the most common application — the collar sits flat against the floor and covers the gap around the pipe cleanly.
Material and Build
Made from high grade polypropylene with a chrome ABS effect finish, these are UK manufactured. Polypropylene handles heat without distorting, which matters when you’re fitting collars close to pipework that cycles between hot and cold regularly. The chrome finish won’t corrode in a damp environment, though it’s worth noting these are a decorative item rather than a structural fixing. They cover the gap — they’re not there to support anything.
At this price point, keeping a few of each common size in the van costs next to nothing and saves the awkward conversation with a customer about the unfinished gap around their new radiator pipes. Stock them in 15mm and 22mm at a minimum, and you’ll use them on almost every heating job.
Pro Tip: Slide the collar onto the pipe before you connect fittings at either end — retrofitting over an already-plumbed pipe is possible but awkward, and you'll lose five minutes you didn't budget for.
Talon chrome pipe cover collars are used wherever a pipe penetrates a finished surface and the gap around it needs to look presentable. That covers central heating flow and return pipes rising through floorboards, cold water supply pipes entering through walls, and waste pipes passing through bathroom or kitchen surfaces. They work in both residential and light commercial settings, and the chrome finish suits any room where a plain white collar would look out of place.
Best For
Central heating pipe penetrations through floors
Radiator pipework in living areas and hallways
Bathroom and kitchen plumbing pipe entry points
Waste and supply pipes through walls
Available In
8mm
10mm
12mm
15mm
18mm
22mm
28mm
35mm
42mm
110mm
Key Features
Chrome ABS effect finish
Single-piece construction for quick fitting
High grade polypropylene material
Heat resistant, suitable for heating pipework
Made in the UK
Decorative cover, not a structural fixing
Not suitable for: Not suitable for use as a structural pipe support or where the collar will bear load. The chrome finish is a decorative ABS effect and is not suitable as a replacement for chrome-plated brass escutcheons in high-specification brassware installations.
Fitting is straightforward. Slide the collar onto the pipe before final connections are made, position it against the wall or floor surface, and it sits in place covering the gap around the penetration. No fixings are required in most applications as the collar rests against the surface under its own weight and the presence of the pipe through the centre.
For retrofit installations where the pipe is already connected, check whether a split collar is more practical. For new installations, always fit the collar before making the final connection at the far end of the pipe run.
Select the correct collar size to match your pipe outside diameter
Slide the collar onto the pipe before completing pipework connections
Feed the pipe through the wall or floor penetration as normal
Push the collar back against the surface to cover the gap around the pipe
Check it sits flush and covers any visible damage or oversized hole
No adhesive or fixings are needed in standard installations
Are these the same as chrome escutcheons or pipe roses?
They serve the same purpose — covering the gap where a pipe goes through a surface — but Talon pipe cover collars are made from polypropylene with a chrome ABS effect finish rather than solid chrome-plated brass. They're lighter, less expensive, and perfectly suitable for standard plumbing and heating installations. If you're fitting high-end brassware throughout, solid brass escutcheons may be more appropriate, but for most domestic heating and plumbing work these are entirely fit for purpose.
What pipe sizes do these chrome collars cover?
The range covers 8mm, 10mm, 12mm, 15mm, 18mm, 22mm, 28mm, 35mm, 42mm and 110mm. That takes in most standard microbore, copper and plastic pipe sizes used in domestic heating and plumbing, plus the 110mm size for soil pipe penetrations.
Talon chrome pipe cover collars are manufactured from high grade polypropylene with a chrome ABS effect overmould or surface finish. Polypropylene offers good resistance to heat cycling, making these suitable for use around central heating pipework. The single-piece construction requires no assembly. Manufactured in the UK to consistent dimensional tolerances across the full size range from 8mm to 110mm.
Material
High grade polypropylene with chrome ABS effect finish
Reviews
There are no reviews yet.