WRAS approved end feed straight tap connector for copper pipework. Available in 15mm x 1/2″, 15mm x 3/4″ and 22mm x 3/4″. Sold in boxes of 10, these are a solid everyday fitting for domestic and commercial plumbing installations.
Available options and pricing for End Feed straight tap connector, with quantity selectors and a running total
Size
SKU
Price
QTY
Total
15mm x 3/4"
30465305
£7.68£9.22
—
22mm x 3/4"
30465309
£12.16£14.59
—
15mm x 1/2"
30465301
£5.76£6.91
—
The end feed straight tap connector is one of those fittings you go through constantly on any plumbing job. Connecting copper pipe to a threaded fitting on a tap, valve or appliance, it does a straightforward job and it needs to do it reliably every time. These are WRAS approved, which matters if you are working on domestic water supplies or any installation where water quality standards apply.
End feed fittings work by soldering the copper pipe directly into the socket. There is no integral solder ring to fall back on, so the joint relies entirely on your technique and the flux and solder you bring to the job. That is not a drawback. For a competent plumber, end feed gives you a cleaner, more controlled joint and tends to be the go-to choice where quality and finish count. It also means you are not paying for solder you might not need.
End Feed Straight Tap Connector Sizes and Where They Fit
Three sizes are available: 15mm x 1/2″, 15mm x 3/4″ and 22mm x 3/4″. The 15mm x 1/2″ is the one you reach for most often, connecting standard 15mm copper to a 1/2″ BSP male thread on a kitchen or bathroom tap. The 15mm x 3/4″ and 22mm x 3/4″ versions cover larger valves, service connections and commercial fitouts where flow rates demand bigger pipework. Worth keeping a box of each on the van if you cover a range of work.
WRAS approval means the fittings are certified for use with wholesome drinking water in the UK. If you are working on properties that require compliance documentation, or you are specifying fittings for a client who wants everything signed off properly, these tick that box without any additional steps on your part.
Buying in Boxes of 10
These are sold in boxes of 10, which is a sensible quantity for trade use. You get enough to cover a multi-tap installation or a full bathroom without running short, and the per-unit cost at bulk works out considerably better than buying loose. A kitchen refit with four or five tap connections, a utility room, and a couple of isolating valves will eat through these quickly enough that buying by the box simply makes more sense.
If you need the end feed straight tap connector across multiple jobs or sites, the pricing here is structured for trade volume. Stock up, save the emergency merchant run, and get on with the work.
Pro Tip: Always use a good quality flux paste and keep your heat focused on the fitting body rather than the pipe, drawing the solder in cleanly rather than flooding the joint from outside.
End feed straight tap connectors are used wherever copper pipework needs to terminate at a threaded fitting. That covers kitchen and bathroom tap tails, isolation valves, washing machine and dishwasher supply points, and commercial plumbing connections to appliances and plant. They are standard on new builds, refurbishments and maintenance work alike. Any plumber running copper pipe to a threaded device will reach for one of these at the end of the run.
Best For
Kitchen and bathroom tap connections
Isolation valve terminations
Appliance supply points
Commercial plumbing installations
New build and refurbishment work
Compatible With
Copper pipe
1/2" BSP male threaded fittings
3/4" BSP male threaded fittings
Standard tap tails
WRAS compliant systems
Key Specifications
WRAS approved for drinking water use
Available in 15mm x 1/2"
Available in 15mm x 3/4"
Available in 22mm x 3/4"
End feed solder type
Sold in boxes of 10
Not suitable for: Not suitable for plastic or push-fit pipe systems without copper pipe adapters. Not intended for compression fitting applications.
Clean the outside of the copper pipe and the inside of the fitting socket thoroughly with wire wool or emery cloth until both surfaces are bright. Apply flux paste to both surfaces before assembling. Hold the fitting in position on the pipe and apply heat evenly to the fitting body with a plumber's torch until the flux begins to activate.
Touch solder to the edge of the socket and allow it to be drawn in by capillary action. A clean joint uses very little solder. Remove the heat, allow to cool undisturbed, and wipe away any excess flux residue once the joint has set. For the threaded end, use PTFE tape or jointing compound on the male thread before making up the connection.
Cut copper pipe cleanly and remove any burrs with a deburring tool or file
Clean the pipe end and the fitting socket with wire wool or emery cloth to a bright finish
Apply flux paste to both the pipe end and the inside of the fitting socket
Push the pipe fully into the fitting socket and check alignment
Apply heat from a plumber's torch to the fitting body, moving the flame to distribute heat evenly
Touch lead-free solder to the joint edge once the flux activates and allow capillary action to draw it in
Remove heat immediately once a complete ring of solder is visible around the joint
Allow to cool without moving the joint, then wipe away flux residue with a damp cloth
Apply PTFE tape or jointing compound to the male thread before connecting the tap tail or valve
Do I need to supply my own solder and flux with end feed fittings?
Yes. Unlike solder ring fittings, end feed connectors contain no integral solder. You will need to apply flux paste to both surfaces before heating and feed lead-free solder into the joint yourself. This gives you full control over the joint but does require the correct materials on hand.
Are these fittings suitable for use on drinking water systems?
Yes. These end feed straight tap connectors are WRAS approved, meaning they meet the requirements for use on wholesome water supplies in the UK. They are suitable for domestic hot and cold water systems and commercial drinking water installations.
Manufactured from dezincification resistant brass to meet WRAS approval requirements for drinking water contact. End feed construction relies on capillary soldering technique for a leak-free joint. BSP threaded female end accepts standard tap tails and valve connections. Suitable for use on hot and cold water supplies within standard domestic and commercial pressure ranges.
Fitting Type
End Feed Straight Tap Connector
Material
Brass
Approval
WRAS Approved
Thread Standard
BSP (British Standard Pipe)
Available Sizes
15mm x 1/2", 15mm x 3/4", 22mm x 3/4"
Solder Type
End Feed (solder not included)
Box Quantity
10
Size
15mm x 1/2", 15mm x 3/4", 22mm x 3/4"
Box Quantity
10
Reviews
There are no reviews yet.
Be the first to review “End Feed straight tap connector”Cancel Reply
Reviews
There are no reviews yet.