Progressive Reciprocating Saw Blade – Metal/Wood 200mm 6-12tpi – Pack of 5 – S3456XF
SKU: S3456XF-RB61
Categories: Power Tool Blades, Reciprocating Sabre Saw Blades, Reciprocating Progressive Saw Blades, Wood & Metal Cutting Bi-Metal Reciprocating Saw Blades
Tag: reciprocating
£14.95£17.94 EX VATINC VAT
Bi-metal progressive reciprocating saw blade, 200mm with 6-12tpi variable tooth pitch. Cuts thin metal, wood, nailed wood, chipboard and profiles. Universal shank fits most reciprocating saw machines. Pack of 5.
The S3456XF 200mm metal wood reciprocating saw blade is a bi-metal progressive blade built for the kind of mixed-material cutting that comes up constantly on site. Thin steel sections, timber with nails in it, chipboard, profiles — this blade handles the lot without swapping out mid-job. The 6-12tpi progressive tooth pitch is the key here: coarser teeth at the back for fast aggressive cutting, finer teeth toward the tip for cleaner entry and better control on thinner material. It’s a practical design that reduces snagging and blade deflection on sheet metal and light steel profiles.
Progressive blades like this one have largely replaced fixed-pitch blades in mixed-trade toolkits for good reason. When you’re cutting through a timber frame that’s had nails fired into it over the years, or ripping through a composite panel that’s part board and part metal fixing, a single tpi rating is always a compromise. The variable pitch sidesteps that problem. The bi-metal construction — high-speed steel teeth bonded to a flexible alloy body — keeps the teeth sharp through harder material while the blade body flexes rather than snapping under lateral stress.
Where the S3456XF 200mm Blade Gets Used
This is a workhorse demolition and general cutting blade. It turns up in plumbing and heating work where pipes run through timber noggins, in shop fitting where MDF and metal trim need cutting in the same run, and in general building work where speed matters more than a cabinet-quality finish. Roofers use similar blades for cutting through sarking board with nails still in, and groundworkers reach for them when trimming conduit and timber in the same job. The 200mm length gives useful reach into awkward spaces without the blade feeling uncontrollable.
Fitting and Compatibility
The universal shank fits the vast majority of reciprocating saw machines on the market. Bosch, DeWalt, Milwaukee, Makita — if you’ve got a recip saw, these blades will seat correctly. No adaptor needed, no faffing about. Pack of five means you’ve got spares to hand when one gets chewed through a hidden fixing. At this price point, it’s worth keeping a pack in the van rather than hunting round a merchant at half seven in the morning.
Pro Tip: When cutting thin metal profiles, let the saw do the work at a lower stroke rate rather than forcing the pace — pushing too hard on thin sheet causes the blade to skate and the teeth to load up fast, killing the blade in minutes.
This blade covers the kind of cutting that comes up on nearly every trade job: timber framing, sheet materials, light steel sections, plastic profiles and composite panels. It's well suited to demolition and strip-out work where you're cutting through boards that may contain hidden nails or fixings. Plumbers and first-fix electricians use blades like this when cutting timber noggins with cables or pipes nearby, and shopfitters reach for them when trimming both board and metal in a single pass.
Best For
- Thin metal and steel profiles
- Timber and nailed wood
- Chipboard and MDF
- Plywood and sheet materials
- Mixed-material demolition cutting
- Plastic and composite profiles
Compatible With
- Bosch reciprocating saws
- DeWalt reciprocating saws
- Milwaukee reciprocating saws
- Makita reciprocating saws
- All standard universal shank recip saws
Key Specifications
- Blade length: 200mm
- TPI: 6-12 progressive
- Construction: bi-metal
- Shank: universal fitting
- Pack quantity: 5
- Reference: S3456XF
Not suitable for: Not suited to cutting hardened steel, cast iron or stainless sections of any significant thickness. Also not the right blade for finish-quality cuts where a clean edge is required.
Fit the blade to your reciprocating saw with the machine unpowered. Ensure the shank is fully seated and the locking mechanism is engaged before starting. For timber and board, use a higher stroke rate and moderate pressure. For thin metal, drop the stroke rate and keep the blade moving steadily to prevent tooth loading.
On nailed wood, slow down slightly as you approach known nail lines — the bi-metal construction handles the odd nail, but hammering through fixings at full pace shortens blade life noticeably. Support the workpiece where possible to reduce vibration and keep the cut line true.
- Ensure the reciprocating saw is switched off and battery or power is disconnected before fitting the blade
- Insert the universal shank fully into the blade clamp until it locks securely
- Select an appropriate stroke rate on your saw — higher for wood and board, lower for thin metal
- Begin the cut with light pressure to establish the cut line, then increase feed rate once the blade is tracking correctly
- On thin metal or profiles, keep the blade moving at a steady pace rather than pushing hard — letting the teeth work prevents overloading
- When cutting nailed timber, ease off slightly as the blade reaches known fixing positions
- Inspect the blade after heavy use and replace if teeth appear stripped or the blade has developed a set
Will these blades fit my reciprocating saw?
Almost certainly yes. The universal shank is the standard fitting used across the vast majority of reciprocating saw brands including Bosch, DeWalt, Milwaukee and Makita. If your machine accepts standard recip saw blades, these will fit without an adaptor.
What is the advantage of a progressive blade over a standard fixed-tpi blade?
A progressive blade has a variable tooth pitch — coarser toward the body of the blade for fast cutting, finer toward the tip for cleaner entry and better performance on thin material. On site where you're cutting through a mix of timber, board and metal fixings in the same session, it's a more practical choice than committing to a single tpi that will always be a compromise somewhere.
Bi-metal construction pairs a high-speed steel tooth edge with a flexible alloy steel body, giving the blade good tooth hardness without the brittleness of a fully hardened blade. The 6-12tpi progressive pitch is ground to handle mixed-material cuts effectively. At 200mm, the blade length is suitable for both general cutting and working in moderately confined spaces.
| Blade Length | 200mm |
|---|---|
| TPI | 6-12 progressive |
| Construction | Bi-metal |
| Shank Type | Universal |
| Application | Metal and wood |
| Pack Quantity | 5 |
| SKU Reference | S3456XF |
| Box Quantity | 5 |
|---|---|
| Size | 200mm |
Be the first to review “Progressive Reciprocating Saw Blade – Metal/Wood 200mm 6-12tpi – Pack of 5 – S3456XF”Cancel Reply
You may also like…

Demolition Reciprocating Saw Blades
From £9.95£11.94 EX VATINC VAT
Reciprocating Saw Blades – Wood & Metal Cutting – BiMetal – S1411DF
£9.99£11.99 EX VATINC VAT
ABRACS 8pc Mixed Reciprocating Saw Blade Set Wood & Metal
£13.98£16.78 EX VATINC VAT
Related products

Reciprocating Saw Blades – Wood Cutting – High Carbon Steel – S1531L
£4.93£5.92 EX VATINC VAT
Starrett 3X Power Demolition Reciprocating Saw Blades 150mm 10-14tpi Pk5
£8.46£10.15 EX VATINC VAT
Starrett Pro Bi-Metal Reciprocating Saw Blade Set 5pc Mixed
£11.96£14.35 EX VATINC VAT
Reciprocating Saw Blades – Metal Cutting – Bi-Metal – S1122BF
£9.42£11.30 EX VATINC VAT

Reviews
There are no reviews yet.