Two-part trade strength mitre bond kit from Timco. Apply the adhesive, spray the activator, and you have an instant bond on wood, MDF, PVCu, metal, rubber, ceramics and more. Handles from -55°C to +80°C.
The Timco Premium Mitre Bond Adhesive Kit is a two-part cyanoacrylate system built for fast, reliable bonding on site. One part is the adhesive, the other is the activator — spray the activator onto one surface, apply adhesive to the other, press them together and the bond sets in seconds. That is not marketing language, that is genuinely how fast it works. If you have ever held a mitre joint by hand for three minutes waiting for PVA to decide what it wants to do, this kit will change your day considerably.
The 200ml adhesive and 50g activator come as a ready-to-use kit, which means no hunting around for a matching activator or buying components separately. Everything you need is in the box. The adhesive itself handles small gap filling too, which is useful when timber is not quite as straight as the merchant said it was.
Where the Mitre Bond Adhesive Kit Earns Its Keep
This system is popular with carpenters, joiners and shopfitters who need to make mitre joints quickly and cleanly without clamps. It is also well used in the sign and display trade, where bonding ceramics, leather or rubber to other substrates is a regular requirement. The temperature range of -55°C to +80°C means it holds up in cold stores, roof spaces in summer, and anything in between. That kind of performance envelope covers most of what you would encounter on a commercial fit-out or a domestic refurb.
Because the activator drives cure speed, you have a degree of control. Apply the adhesive and take your time positioning the component, then trigger the bond when you are ready. That small amount of working flexibility makes a noticeable difference when you are lining up mouldings or cladding that needs to be exactly right.
Suitable for PVCu, wood, MDF, metal, rubber, ceramics and leather. This is a trade-only product and is priced accordingly. At under three pounds for a full kit, it is difficult to argue with.
Pro Tip: Spray the activator onto one surface only and apply the adhesive to the other — putting both on the same piece will trigger the bond before you have made contact and you will end up with a very expensive finger.
This kit is used wherever a fast, permanent bond is needed without the wait. Carpenters and joiners use it daily for mitre joints on architrave, skirting and coving. Shopfitters use it on display units, panelling and cladding. It bonds PVCu window trims, MDF components, ceramic tiles, rubber seals, leather panels and metal fittings. Anywhere you need a clamp-free, instant-set bond on a variety of substrates, this two-part system does the job quickly and cleanly.
Best For
Mitre joints on architrave and skirting
PVCu trims and window boards
MDF panelling and cladding
Sign and display fabrication
Small gap filling on timber
Compatible Surfaces
Wood and MDF
PVCu
Metal
Rubber
Ceramics
Leather
Key Properties
Instant bond with activator
Temperature resistant -55°C to +80°C
Two-part system: 200ml adhesive + 50g activator
Small gap filling capability
No clamps required
Trade strength formulation
Not suitable for: Not intended for structural load-bearing applications or use on wet or heavily contaminated surfaces. Clean, dry substrates will always give better results with cyanoacrylate-based systems.
Clean both surfaces before you start. Any grease, dust or moisture will compromise the bond, and cyanoacrylate systems are less forgiving than PVA when it comes to surface prep. Dry fit the components first so you know exactly where everything needs to land once you trigger the bond.
Spray the activator onto one surface and apply the adhesive to the other. Bring the two surfaces together firmly and hold for a few seconds. The bond sets almost immediately. For gap filling, apply a small amount of adhesive into the gap and mist activator over the top to cure.
Dry fit the components before bonding to confirm the joint is correct
Clean both surfaces thoroughly to remove dust, grease and any moisture
Spray the activator onto one surface using the included applicator
Apply the adhesive to the opposite surface, keeping the amount consistent
Bring the two surfaces together and apply firm, even pressure
Hold for a few seconds until the bond sets, then release
How long does the bond take to set?
With the activator applied, the bond sets in seconds. The exact time depends on the surfaces and how evenly the activator is applied, but you are typically looking at five to fifteen seconds before the joint is firm enough to handle.
Can this kit be used on PVCu window trims and mouldings?
Yes, PVCu is one of the primary uses for this system. It bonds well to PVCu window boards, architrave, cills and trim without the need for clamps or extended drying time.
Does the kit include both the adhesive and the activator?
Yes. The kit contains a 200ml adhesive and a 50g activator. Both parts are included, so there is no need to source them separately.
The Timco Premium Mitre Bond is a cyanoacrylate-based adhesive system. The activator accelerates the polymerisation of the adhesive on contact, producing a near-instant cure. The cured bond is temperature resistant across a range of -55°C to +80°C, making it suitable for both cold environments and applications exposed to moderate heat. The system also has limited gap-filling capability for minor surface irregularities.
Adhesive Volume
200ml
Activator Weight
50g
Bond Type
Cyanoacrylate (two-part with activator)
Temperature Resistance
-55°C to +80°C
Set Time
Seconds with activator applied
Compatible Surfaces
Wood, MDF, PVCu, metal, rubber, ceramics, leather
Pack Contents
1 x 200ml adhesive, 1 x 50g activator
Reviews
There are no reviews yet.
Be the first to review “Timco Premium Mitre Bond Adhesive Kit 200ml / 50g”Cancel Reply
Reviews
There are no reviews yet.