Everbuild Gun A Nail Standard is a high strength, gap-filling grab adhesive with a solvent free formula. Works on most building substrates where at least one surface is porous. Good for general building and home improvement work.
Everbuild Gun A Nail Standard is a reliable, solvent free grab adhesive built for general building and home improvement use. It is based on a tackified system that grabs quickly and fills gaps as it bonds, which saves time on surfaces that aren’t perfectly flat or flush. If you’ve been looking for an everbuild gun a nail grab adhesive that does the everyday jobs without any fuss, this is it.
The formula is solvent free, which matters indoors. No sharp fumes, no need to evacuate the room, and safer to use in poorly ventilated spaces than older solvent-based alternatives. It comes in a standard cartridge format, so any decent skeleton gun will do the job.
Where Gun A Nail Standard Gets Used
This adhesive is aimed squarely at construction and DIY tasks where you need a dependable, general-purpose bond. Fixing architrave, skirting boards, plasterboard, timber battens, coving, cladding panels — the kind of work that comes up every single day on site or in a domestic setting. It handles a wide range of substrates, provided at least one of the surfaces being bonded is porous. That covers most common building materials, so in practice it fits neatly into most workflows.
Gap Filling Performance
One of the more useful properties of Gun A Nail Standard is its gap-filling nature. Surfaces on site are rarely perfect, and a contact adhesive with no body to it will leave you with a weak bond the moment there’s a slight recess or uneven area. The thick consistency here bridges small gaps rather than simply failing across them.
Apply at temperatures between +4°C and +40°C. Below that lower limit the adhesive won’t perform correctly, so on cold mornings let the cartridge warm up to room temperature before you start. A bucket of warm water for ten minutes does the trick if it’s been sitting in an unheated van overnight. The everbuild gun a nail grab adhesive performs best when both surfaces are clean, dry, and free of dust or grease before application.
Pro Tip: If the cartridge has been left in a cold van overnight, sit it in a bucket of warm water for ten minutes before use — cold adhesive won't flow or bond properly, and you'll waste half the tube trying to force it through.
Gun A Nail Standard is used across general building work wherever a fast, gap-filling bond is needed on porous substrates. Fixing skirting boards, architrave, coving, timber battens, and plasterboard are the bread and butter applications. It also gets used for internal cladding panels, decorative mouldings, and general fixing tasks during fit-out work. Joiners, general builders, and capable DIYers all reach for it regularly because it handles the kind of awkward everyday bonding jobs where screws or nails would either crack the material or simply take too long.
Best For
Skirting boards and architrave
Coving and decorative mouldings
Plasterboard fixing
Timber battens and cladding panels
General building and fit-out work
Compatible Surfaces
Timber and MDF
Plasterboard
Concrete and block
Brick
Plaster
At least one substrate must be porous
Key Properties
Solvent free formula
High strength initial grab
Gap filling consistency
Application range +4°C to +40°C
Standard cartridge format
Low fume, safer for indoor use
Not suitable for: Not suitable for bonding two non-porous surfaces together, such as glass to glass or metal to metal. Do not use below +4°C as the adhesive will not bond correctly.
Load the cartridge into a standard skeleton gun. Cut the nozzle tip to your preferred bead size and puncture the foil seal if present. Apply an even bead or spots of adhesive to one surface, press the two surfaces firmly together, and hold or support until the initial grab takes hold.
Make sure both surfaces are clean, dry, and free from dust, grease, and loose material before you start. On porous substrates the bond develops as moisture is absorbed into the surface, so pressing firmly and allowing adequate contact time will give a stronger result. The adhesive should be at room temperature before application — if it's been stored in cold conditions, bring it up to working temperature first.
Ensure both surfaces are clean, dry, and free from dust, grease, and loose material
Bring the cartridge to room temperature if it has been stored in cold conditions
Load the cartridge into a standard skeleton gun
Cut the nozzle to the required bead size and pierce the foil seal
Apply a continuous bead or evenly spaced spots to one surface
Press the two surfaces firmly together with even pressure
Hold in position until the initial grab is sufficient to support the material
Allow full cure before applying any significant load to the bond
Can I use Gun A Nail Standard to bond two non-porous surfaces?
No. The adhesive requires at least one of the substrates to be porous in order to bond correctly. It won't work reliably between two non-porous surfaces such as glass, metal, or PVC.
What gun does this cartridge fit?
It fits a standard skeleton or frame gun, which is the most common type used on site. If you already have a gun for mastic or sealant cartridges, it will almost certainly work with this adhesive.
Is it safe to use indoors?
Yes. The solvent free formula means it produces far fewer fumes than older solvent-based grab adhesives, making it much more practical for indoor use in kitchens, living rooms, and spaces where ventilation is limited. Reasonable airflow is still a good idea, but it won't clear a room.
Everbuild Gun A Nail Standard is formulated on a tackified solvent free polymer system. The thick, paste-like consistency gives it gap-filling properties that improve bond performance on uneven or slightly irregular surfaces. It is designed for use at temperatures between +4°C and +40°C, and the cartridge should be at ambient room temperature before application to ensure correct flow and adhesion.
Brand
Everbuild
Product Type
Solvent Free Grab Adhesive
Formula
Tackified solvent free system
Application Temperature Range
+4°C to +40°C
Substrate Requirement
At least one porous substrate required
Format
Standard cartridge
SKU
GANN3
Product Type
Fast Grab Construction Adhesives
Reviews
There are no reviews yet.
Be the first to review “GUN A NAIL Standard – Everbuild (Solvent Free Grab Adhesive)”Cancel Reply
Reviews
There are no reviews yet.