Soudal Fix All Crystal is a single-component, crystal clear MS-Polymer adhesive and sealant. Neutral cure, elastic, and isocyanate-free. Bonds and seals glass, plastics, metals and most building substrates inside and out.
Soudal Fix All Crystal Clear is a single-component sealant and adhesive based on MS-Polymers, curing to a fully transparent, flexible bond. Where most grab adhesives leave a visible bead behind, this one essentially disappears — which makes it genuinely useful when you are bonding glass, clear polycarbonate panels, decorative trims, or anything where a white or grey line would ruin the finish. It is neutral curing, solvent-free, and free of isocyanates, so it sits comfortably in well-ventilated and indoor spaces without the sharp chemical smell you get from some alternative formulations.
The MS-Polymer base gives Fix All Crystal its elasticity after cure. Joints can move slightly without the bond cracking, which matters on exterior applications where thermal expansion is a factor. It extrudes cleanly even in cold weather down to around 5°C, so it keeps working on site in autumn and winter when other adhesives start to stiffen in the cartridge. Application is straightforward — standard manual or pneumatic caulking gun, no mixing, no priming on most surfaces.
Where Soudal Fix All Crystal Gets Used
Bond strength is genuinely strong across a wide range of substrates: glass, metals, most plastics, timber, ceramics, painted surfaces, and common construction boards. The transparency is the key selling point — wherever you need an adhesive joint that stays invisible, Soudal Fixall Crystal Clear is the practical answer. It can be overpainted, though a quick compatibility test is sensible before you commit on a large area, particularly with alkyd-based paints.
It handles interior and exterior bonding and sealing applications, and the UV stability is good for outdoor use, though prolonged extreme exposure can cause slight discolouration over time. A few firm limitations to know before you buy: not suitable for dilatation joints, not for areas of continuous water immersion, not for use on natural stone, and not a glazing sealant for structural glazing applications. Use it within those boundaries and it performs reliably.
Pro Tip: When tooling Fix All Crystal, use a damp finger or a spatula wetted with soapy water rather than a dry tool, as this gives you a cleaner finish and prevents the material from dragging or picking up.
Fix All Crystal is used wherever a transparent, flexible bond or seal is needed on interior and exterior construction work. Typical jobs include bonding glass splashbacks, fixing clear decorative panels, sealing around glass balustrades, adhering mirror tiles, and securing transparent or translucent sheet materials to frames. It is used by glaziers, shopfitters, kitchen and bathroom installers, and general builders who need a neat finish with no visible adhesive line. The product suits both bonding and sealing functions in a single application, saving the step of applying a separate sealant over an adhesive bead.
Best For
Transparent and invisible bonding
Glass and clear panel fixing
Interior and exterior sealing
Decorative trims and mirrors
Flexible joints on moving substrates
Compatible Surfaces
Glass
Metals
Most plastics (compatibility test advised)
Timber and MDF
Ceramics and tiles
Painted surfaces
Most construction boards
Key Properties
Fully crystal clear cure
MS-Polymer based, solvent-free
Isocyanate-free formulation
Neutral cure, elastic bond
Good UV stability
Overpaintable
Applicable from 5°C to 35°C
Not suitable for: Not suitable for dilatation joints, structural glazing, sanitary wet areas, or natural stone substrates. Do not use where continuous water immersion is expected.
Apply Fix All Crystal with a standard manual or pneumatic caulking gun. The nozzle can be cut to suit the joint width required, keeping in mind the product is designed for connecting joints up to 1mm wide rather than large gap-filling. Clean substrates thoroughly before application, removing dust, grease and any loose material, as contamination is the most common cause of bond failure with any MS-Polymer adhesive.Tool the bead immediately after application using a damp finger or spatula. Clean any excess from the surface straight away using Fix All Cleaner before the product begins to cure, as it is considerably harder to remove once set. Allow the joint to cure fully before loading or stressing the bond.
Clean both substrates thoroughly, removing grease, dust, and any loose material
Cut the nozzle to the required diameter and fit to the cartridge
Load the cartridge into a manual or pneumatic caulking gun
Apply a consistent bead into the joint or onto the bonding surface
Press components together firmly and align them before the product skins
Tool the bead smooth immediately using a damp finger or spatula
Remove any excess product straight away with Fix All Cleaner before curing begins
Allow full cure before applying load or stress to the joint
Can Soudal Fix All Crystal be used to seal a shower or wet room?
No. Fix All Crystal is not suitable for sanitary applications or areas with continuous water immersion. For wet rooms and showers, you need a dedicated sanitary silicone or an MS-Polymer product rated for those conditions.
Will Fix All Crystal stay clear over time on an outdoor application?
UV stability is good and it is suitable for exterior use, but some discolouration is possible under extreme or prolonged UV exposure over the long term. For most exterior bonding jobs it performs well, but if permanent optical clarity outdoors is critical, it is worth testing on a sample first.
Can I use this product on natural stone such as marble or granite?
No. Fix All Crystal should not be used on natural stone. The adhesive can cause the stone surface to appear wet or stained, and because the product is crystal clear, that discolouration is visible through the joint. Use a product specifically formulated for natural stone instead.
Fix All Crystal is based on MS-Polymer technology, which combines the flexibility of silicone with the paintability and adhesion of polyurethane, without the isocyanates or solvents associated with either. It cures by moisture to form a permanently elastic, transparent bond. The formulation is neutral curing, making it compatible with sensitive substrates that acidic or alkaline cure systems can attack. Application temperature range is 5°C to 35°C.
Product Type
MS-Polymer adhesive and sealant
Cure Type
Moisture cure, neutral
Colour
Crystal clear
Application Temperature
5°C to 35°C
Maximum Joint Width
1mm (connecting joints)
Isocyanate-Free
Yes
Solvent-Free
Yes
Overpaintable
Yes (compatibility test recommended)
Application Method
Manual or pneumatic caulking gun
Brand
Soudal
Product Type
Fast Grab Construction Adhesives
Reviews
There are no reviews yet.
Be the first to review “Soudal Fixall – Crystal Clear”Cancel Reply
Reviews
There are no reviews yet.