WRAS approved end feed adaptors in a full range of sizes from 15mm to 28mm, with male and female BSP threads. For connecting copper pipe to threaded fittings on domestic and commercial installations.
Available options and pricing for End Feed adaptor, with quantity selectors and a running total
Size
QTY
SKU
Price
QTY
Total
15mm x 1/2" male
1
30418609
£0.67£0.80
—
15mm x 3/4" male
1
30418613
£1.50£1.80
—
22mm x 3/4" male
1
30418617
£1.30£1.56
—
28mm x 1" male
1
30418625
£1.68£2.02
—
15mm x 1/2" female
1
30421709
£0.77£0.92
—
22mm x 3/4" female
10
30421713
£11.04£13.25
—
The end feed adaptor is one of those fittings that lives quietly at the back of the van but earns its keep on practically every job. Whether you’re connecting copper pipework to a threaded valve, tank connector, or appliance inlet, this is the fitting that bridges the gap between soldered copper and BSP threads. Available in a range of sizes from 15mm x 1/2″ up to 28mm x 1″, with both male and female BSP options to suit the connection you’re working with.
All fittings are WRAS approved, which matters when you’re working on potable water systems. WRAS approval means the materials have been independently tested and confirmed as suitable for contact with drinking water — something specifiers and building control increasingly want to see in writing, and something any conscientious plumber should be using as standard anyway.
Where End Feed Adaptors Get Used
End feed fittings suit plumbers who are comfortable with a torch and solder. There’s no integral solder ring to rely on, which actually gives you more control over the joint if you know what you’re doing. The fitting heats evenly, you feed solder into the mouth of the fitting, and capillary action does the rest. Clean, consistent, and not reliant on however much solder someone decided to press into a pre-soldered fitting at the factory.
The male and female BSP variants cover the most common scenarios you’ll encounter. Female adaptors accept a male threaded fitting or valve tail. Male adaptors thread into a female port on a pump, valve body, or manifold. Getting the gender right before you start is one of those things that sounds obvious, but there’s a reason plumbers’ merchants sell a lot of both.
Size Options
The range covers 15mm x 1/2″ female, 15mm x 1/2″ male, 15mm x 3/4″ male, 22mm x 3/4″ female, 22mm x 3/4″ male, and 28mm x 1″ male. That covers the majority of domestic and light commercial work without needing to source oddities. Available individually or in boxes of ten, which makes sense if you’re stocking up before a larger job or just want to avoid the van rummage that costs you fifteen minutes every Tuesday morning.
At under a pound each, these are competitively priced for a WRAS approved fitting. Buy in tens and the saving is worth it over the course of a busy month.
Pro Tip: Always wire brush the outside of the copper pipe end and the inside of the fitting socket before fluxing — end feed joints fail far more often from poor prep than poor technique, and a dull pipe surface will cause solder to bead rather than flow cleanly into the joint.
End feed adaptors are used wherever a copper pipe run needs to terminate at or connect to a BSP threaded fitting. Common applications include connecting pipework to isolation valves, gate valves, ball valves, tank connectors, pump inlets, and appliance tails. They're a staple on domestic heating and hot and cold water systems, and equally at home on light commercial plumbing installations where copper is specified.
Best For
Copper to BSP thread connections
Domestic hot and cold water systems
Central heating pipework
Valve and pump connections
Light commercial plumbing
Available In
15mm x 1/2" female
15mm x 1/2" male
15mm x 3/4" male
22mm x 3/4" female
22mm x 3/4" male
28mm x 1" male
Key Features
WRAS approved for potable water use
End feed solder-type fitting
BSP thread compatibility
Available individually or in boxes of 10
Suitable for both male and female BSP connections
Not suitable for: Not suitable for use with plastic or push-fit pipe systems. Not intended for gas pipework or high-pressure industrial applications.
Clean the outside of the copper pipe end with wire wool or a pipe cleaning brush until the surface is bright. Clean the inside of the fitting socket the same way. Apply flux to both surfaces before assembling the joint.
Heat the fitting evenly with a blowtorch, moving the flame around the body rather than holding it in one spot. When the flux begins to sizzle and the fitting is up to temperature, touch solder to the mouth of the socket and allow capillary action to draw it in. A full ring of solder showing at the joint face indicates a sound connection. Allow to cool before disturbing and wipe away excess flux once cool.
Cut copper pipe square and deburr the end inside and out
Wire brush the pipe end and fitting socket until both surfaces are clean and bright
Apply flux paste to the pipe end and the inside of the fitting socket
Push the fitting firmly onto the pipe to the full depth of the socket
If threading onto a BSP connection, apply PTFE tape to male threads before assembly
Heat the fitting body evenly with a blowtorch until flux activates
Feed solder into the mouth of the socket and allow it to draw in by capillary action
Check for a complete solder ring visible around the joint face
Allow the joint to cool naturally before pressure testing
Wipe away any residual flux with a damp cloth once cool
What does WRAS approved mean and why does it matter?
WRAS stands for the Water Regulations Advisory Scheme. A WRAS approved fitting has been independently tested and confirmed as safe for use in contact with drinking water. For plumbers working on potable water installations in the UK, using WRAS approved fittings is best practice and is increasingly expected by specifiers and building control. It also protects you professionally if a water quality issue ever comes into question.
What is the difference between a male and female end feed adaptor?
A male adaptor has an external BSP thread and connects into a female threaded port, such as the body of a valve or pump. A female adaptor has an internal BSP thread and accepts a male threaded fitting or valve tail. Check the thread type on the component you are connecting to before ordering, and make sure the BSP size matches as well as the copper pipe diameter.
Manufactured from copper alloy and supplied as end feed solder-type fittings conforming to BS EN 1254-4. The fittings are WRAS approved, confirming suitability for use in contact with potable water in accordance with UK water regulations. BSP threads conform to BS 21 and are compatible with standard UK plumbing components. Available in compression sizes from 15mm to 28mm with BSP thread sizes from 1/2" to 1".
Approval
WRAS Approved
Fitting Type
End Feed (Solder Type)
Thread Standard
BSP (British Standard Pipe)
Available Sizes
15mm x 1/2", 15mm x 3/4", 22mm x 3/4", 28mm x 1"
Thread Configurations
Male and Female BSP
Standard
BS EN 1254-4
Pack Options
1 or 10
Size
15mm x 1/2" female, 15mm x 1/2" male, 15mm x 3/4" male, 22mm x 3/4" female, 22mm x 3/4" male, 28mm x 1" male
Box Quantity
1, 10
Reviews
There are no reviews yet.
Be the first to review “End Feed adaptor”Cancel Reply
Reviews
There are no reviews yet.